Renault Clio: Bonnet lock: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Remove the front bumper (see 55A, Exterior protection,
Front bumper: Removal - Refitting, 55A-1).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
- Remove the bonnet catch bolts (1).
- Remove the clip (2) using offset adjusting pliers.
- Unclip the sheath stop from the bonnet opening cable.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
- Clip on:
- the clip (2),
- the bonnet opening cable.
- Pretighten the bonnet catch bolts.
- Adjust the flush fittings and shut lines on the bonnet.
- Tighten to torque the bonnet catch bolts (21 Nm).
II - FINAL OPERATION
- Refit the front bumper (see 55A, Exterior protection,
Front bumper: Removal - Refitting, 55A-1).
Tailgate lock: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
Note:
If there is an electrical fault it is possible to open
the tailgate manually.
Carry out this operation from inside the vehicle.
- Unlock the tailgate lock by pushing lug (1) with a
screwdriver.
- Remove the tailgate trim (see Tailgate trim: Removal
- Refitting) (73A, Non-side opening elements
trim).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
- Remove the tailgate lock bolts (2).
- Partially remove the tailgate lock by pressing on the pre-retaining clip
(3).
- Disconnect the tailgate lock connector.
- Remove the tailgate lock.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
- Connect the tailgate lock connector.
- Position the tailgate lock using the pre-retaining clip.
- Torque tighten the tailgate lock bolts (8 N.m).
II - FINAL OPERATION
- Carry out a function test.
- Refit the tailgate trim (see Tailgate trim: Removal -
Refitting) (73A, Non-side opening elements trim).
Tailgate strut: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
Note the direction in which the tailgate struts are
fitted before removal.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
- Extract the clips (1) without removing them
- Remove the struts whilst holding the tailgate.
REFITTING
I - REFITTING PREPARATION OPERATION
- Position the clips on the struts.
II - REFITTING OPERATION FOR PART
CONCERNED
- Offer up and clip in the struts.
Tailgate opening switch: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Remove the tailgate trim (see Tailgate trim: Removal
- Refitting) (MR 393, 73A, Non-side opening
element trim).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
- Access the control via the tailgate interior.
- Squeeze the clips (1).
- Take out the control.
- Disconnect the connector.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
- Connect the connector.
- Clip on the tailgate opening control.
II - FINAL OPERATION.
- Refit the tailgate trim (see Tailgate trim: Removal -
Refitting) (MR 393, 73A, Non-side opening element
trim).
READ NEXT:
PANORAMIC SUNROOF
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
Unclip the roof opening control using a flat-blade screwdriver (1).
Disconnect the connectors.
REFITTING
REFITTING OPERATION FOR
PANORAMIC SUNROOF
REMOVAL
I - REMOVAL PREPARATION OPERATION
Open the moving panel.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Remove the rear bolts (1) from the mobile panel.
Remove:
th
PANORAMIC SUNROOF
IMPORTANT
Before working on or near a safety system component;
make sure that the airbag computer is
locked using the Diagnostic tool. When this
function is activated, all the trigg
SEE MORE:
Front seat belt: Removal - Refitting
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or pretensioners),
lock the airbag computer using the diagnostic
tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning
D4F or F4R or K4J or K4M or M4R
IMPORTANT
Wear leaktight gloves (Nitrile type) for this operation.
IMPORTANT
Always wear protective gear (gloves, goggles and
breathing masks).
Note:
Be sure to work in a clean environment so as not to
allow any contamination of the throttle valve.
CLEANING
I - CLEAN
© 2016-2024 Copyright Renault Clio Owners Club