Renault Clio: Underbody heights: Adjustment value

I - MEASURING POINTS

Renault Clio. Underbody heights: Adjustment value

Radius under load:

1 - Front height (W1)

Renault Clio. Underbody heights: Adjustment value

Renault Clio. Underbody heights: Adjustment value

(W1) : Height between the ground and the rear cross member bolt head

2 - Rear height (W2)

Renault Clio. Underbody heights: Adjustment value

Renault Clio. Underbody heights: Adjustment value

(W2) : Height between the ground and the shaft of the rubber bush on the bearing

II - MEASURING PROCEDURE

Note: For measurements (W1) and (W2), take into account the height difference between the plates and the lift.

Measure the heights:

Note: The value of Wx to be entered into the geometry bench is the average of the W1 heights, right-hand and left-hand and of the W2 heights, right-hand and left-hand.

Note: If the measuring points are located in empty space (between the rails of the lift), use a bar.

1 - Plate higher than the lift:

Renault Clio. Underbody heights: Adjustment value

Measure the heights (1), (2), (3).
Example: (1) = 13 cm, (2) = 8 cm, (3) = 10 cm.
Calculate the height Wx:
Wx = height (1) + height (3) - height (2)
Wx = 15 cm

2 - Plate lower than the lift:

Renault Clio. Underbody heights: Adjustment value

Measure the heights (1), (2), (3).
Example: (1) = 8 cm, (2) = 10 cm, (3) = 4 cm.
Calculate the height Wx:
Wx = height (1) + height (2) + height (3)
Wx = 22 cm

III - VEHICLE IN RUNNING ORDER POSITION

VODM (Vehicle in working order) position:

EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT LEVEL EAG

(W1) = 171 +- 13 mm
(W2) = 259 +- 16 mm

EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL SPORT, and WITHOUT ADDITIONAL PACK

(W1) = 156 +- 5 mm
(W2) = 257 +- 16 mm

EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL SPORT, and ADDITIONAL EXTREME PACK

(W1) = 148+7
-14mm
(W2) = 249+ 9
-16mm

Note:

The position of the vehicle varies according to:

READ NEXT:

 Front axle system: Tightening torque

EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT LEVEL EAG EQUIPMENT LEVEL EAC or EQUIPMENT

 Rear axle system: Tightening torque

Rear axle assembly: Adjustment values EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT LE

 Rigid brake pipe: Repair

This procedure applies to copper pipes diameter 4.7 mm. Note: This procedure does not apply to: hybrid pipes (pipe + hose), pipes with diameters 6 mm and 8 mm. REPAIR I - PIPE PREPARATION OPERATI

SEE MORE:

 Brake servo non-return valve: Removal - Refitting

LEFT-HAND DRIVE REMOVAL I - REMOVAL PREPARATION OPERATION K4J or K4M or K9K Remove the engine cover. II - OPERATION FOR REMOVAL OF PART CONCERNED Disconnect the non-return valve (1) at the servo. Pull and turn the non-return valve to release it from the rubber sealing washer. K9K Disconn

 Roof sun blind

Fixed sunroof blind Opening: push handle 1 upwards, then guide it until it opens fully; Closing: pull the handle 1 until it clicks into the catch. If the blind becomes skewed when opening or closing, close fully and then fully open the blind. Front sun visor Lower sun visor

© 2016-2025 Copyright Renault Clio Owners Club