Renault Clio: Speed limiter
The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed.
Controls
- Main “On/Off” switch.
- Limit speed activation, storage and increase switch (+).
- Decreasing the limit speed (-).
- Activation and recall of memorised limit speed (R).
- Speed limiter function standby (with limited speed memory) (O).
Switching on
Press the side switch 1 
. The
indicator
light 6 comes on, lit orange, and the
message “SPEED LIMITER” appears
on the instrument panel, accompanied
by dashes to indicate that the speed
limiter function is activated and waiting
to store a limited speed.
To store the current speed, press switch 2 (+): the limit speed will replace the dashes.
The minimum stored speed is 20 mph (30 km/h).
Driving
When a limited speed has been stored and this speed is not reached, driving is similar to driving a vehicle without the speed limiter function.
Once you have reached the stored speed, no effort on the accelerator pedal will allow you to exceed the programmed speed except in an emergency (refer to information on “Exceeding the limit speed”).
Varying the limit speed
The limit speed may be changed by repeatedly pressing:
- switch 2 (+) to increase speed;
- switch 3 (-) to reduce speed.
| The speed limiter function is in no way linked to the braking system. |
Exceeding the limit speed
It is possible to exceed the limit speed at any time. To do this: press the accelerator pedal firmly and fully (beyond the resistance point).
While the speed is being exceeded, the programmed speed displayed on the instrument panel flashes.
Then, release the accelerator: the speed limiter function will return as soon as you reach a speed lower than the stored speed.
Limited speed cannot be maintained
If driving up or down a steep gradient, the system is unable to maintain the limit speed: the stored speed will flash on the instrument panel information display to inform you of this situation
Putting the function on standby
The speed limiter function is suspended when you press switch 5 (O). In this case, the speed limit remains stored and the message “MEMORISED” accompanied by this speed appears on the instrument panel.
Recalling the limit speed
If a speed has been saved, it can be recalled by pressing switch 4 ((R)).
| When the speed limiter is put on standby, pressing switch 2 (+) reactivates the function without taking into account the stored speed: it is the speed at which the vehicle is moving that is taken into account. |
Switching off the function
The speed limiter function is deactivated
if you press switch 1: in this
case a speed is no longer stored. The
orange instrument panel warning light
goes out, confirming that the
function
is stopped.
READ NEXT:
Cruise control
The cruise control function helps you to
maintain your driving speed at a speed
that you choose, called the cruising
speed.
This cruising speed may be set at any
speed above 20 mph (30 km/h
Parking sensor
Operating principle
Ultrasonic detectors, installed in the
rear bumper (depending on the vehicle),
measure the distance between the
vehicle and an obstacle whilst reversing.
This measurement is
Reversing camera
Operation
Moving into reverse gear, the 1 camera
(located on the tailgate on five-seater
versions or near the number plate lights
on estate versions) provides a view of
the area behind the ve
SEE MORE:
Clutch circuit: Removal - Refitting
JH3 or JR5
Note:
Each time an operation is carried out on the
hydraulic clutch system, bleed the circuit:
between the reservoir and the bleed hole,
between the bleed hole and the clutch release
bearing.
REMOVAL
I - REMOVAL PREPARATION OPERATION
K4J or K4M
Remove the resonator.
Remov
Attachment using the ISOFIX system
Visual installation of five door and estate versions
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
Seat which does not allow a
child seat to be fitted.
Child se
