Renault Clio: Front side door electric window mechanism: Removal - Refitting

Renault Clio III (2005-2013) Service Manual / Mechanisms And Accessories / Side Opening Element Mechanisms / Front side door electric window mechanism: Removal - Refitting

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Remove the front side door trim (see Front side door trim: Removal - Refitting) (72A, Side opening elements trim).

• Open the access flaps (1) and (2) of the window winder mechanism following the marking on the door sealing film (see Door sealing film: Removal - Refitting) (65A, Opening element sealing).
• Remove the front side door sliding window (see 54A, Windows, Front side door sliding window: Removal - Refitting, 54A-4) or keep it in the raised position with masking tape.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Make cuts in the sealing film to access the window winder mechanism bolts (3).

C85

• Unclip the window winder mechanism cable (5).

• Remove bolts (3) and (4).
• Disconnect the electric window mechanism supply connector.
• Remove the window winder mechanism.

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

Note: Check for the presence of washers on the bolts (6), the bolts (7) and the bolts (8) when refitting the window winder mechanism.

The presence of washers ensures correct tightening.

• Refit the window winder mechanism in the door box section.
• Connect the window winder mechanism supply connector.
• Refit the front side door sliding window glass (see 54A, Windows, Front side door sliding window: Removal - Refitting, 54A-4).

Note: When refitting the window winder mechanism, respect the tightening order.

The tightening order ensures the correct alignment of the window winder mechanism and that the window is correctly positioned with the clip.

• Torque tighten the window winder mechanism bolts (6.5 N.m) following the tightening order: bolts (6), bolts (7) and bolts (8).

C85

• Clip on the window winder mechanism cable (5).

• Carry out a function test.

II - FINAL OPERATION

• Close the access flaps and the cuts in the door sealing film (see Door sealing film: Removal - Refitting) (65A, Opening element sealing).
• Refit the front side door trim (see Front side door trim: Removal - Refitting) (72A, Side opening elements trim).
• Initialise the window winder motor (depending on equipment level) (see Electric windows: Initialisation) (87D, Electric windows - Sunroof).

Front side door manual window winder mechanism: Removal - Refitting

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Remove the door trim (see Front side door trim: Removal - Refitting) (72A, Side opening elements trim).

• Open the access flaps (1) and (2) of the window winder mechanism following the marking on the sealing film (see Door sealing film: Removal - Refitting) (65A, Opening element sealing).
• Remove the sliding window (see 54A, Windows, Front side door sliding window: Removal - Refitting, 54A-4) or secure it in the raised position using masking tape.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Make cuts in the sealing film to access the window winder mechanism bolt (3).

C85

• Unclip the window winder mechanism cable (4).

• Remove:
  • the bolts (3),
  • the window winder mechanism.

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

Note: Check for the presence of washers on the bolts (1), the bolts (2) and the bolts (3) when refitting the window winder mechanism.

The presence of washers ensures correct tightening.

• Refit:
  • the window winder mechanism in the door box section,
  • the sliding window (see 54A, Windows, Front side door sliding window: Removal - Refitting, 54A-4).

Note: When refitting the window winder mechanism, respect the tightening order.

The tightening order ensures the correct alignment of the window winder mechanism and that the window is correctly positioned with the clip.

• Torque tighten the window winder mechanism bolts (6.5 N.m) following the tightening order: bolts (1), bolts (2) and bolts (3).

C85

• Clip on the window winder mechanism cable.

• Carry out a function test.

II - FINAL OPERATION

• Close the access flaps and the cuts in the sealing film (see Door sealing film: Removal - Refitting) (65A, Opening element sealing).
• Refit the door trim (see Front side door trim: Removal - Refitting) (72A, Side opening elements trim).

READ NEXT: