Renault Clio: Sequential gearbox converter: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Sequential gearbox converter: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove:
- the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres),
- the front wheel arch liner (see Front wheel arch liner: Removal - Refitting) (MR 393, 55A, Wheel arch liner).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove:
- the retaining belt (1) from the sequential gearbox computer,
- the sequential gearbox computer connector (2),
- the sequential gearbox computer (3).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the sequential gearbox computer,
- the sequential gearbox computer connector,
- the retaining belt from the sequential gearbox computer,
II - FINAL OPERATION.
- Refit:
- the front wheel arch liner (see Front wheel arch liner: Removal - Refitting) (MR 393, 55A, Wheel arch liner).
- the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres),
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove:
- the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres),
- the front wheel arch liner (see Front wheel arch liner: Removal - Refitting) (MR 393, 55A, Wheel arch liner).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove:
- the retaining belt (1) from the sequential gearbox computer,
- the sequential gearbox computer connector (2),
- the sequential gearbox computer (3).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the sequential gearbox computer,
- the sequential gearbox computer connector,
- the retaining belt from the sequential gearbox computer,
II - FINAL OPERATION.
- Refit:
- the front wheel arch liner (see Front wheel arch liner: Removal - Refitting) (MR 393, 55A, Wheel arch liner).
- the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres),
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
READ NEXT:
Sequential gearbox gear lever: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
Disconnect the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Remove the
Sequential gearbox oil: Specifications
5-SPEED MANUAL SEQUENTIAL GEARBOX
I - GEARBOX TYPE/OIL TYPE CORRELATIONS:
II - STANDARDS AND PART NUMBERS OF THE
VARIOUS RECOMMENDED OILS:
Sequential gearbox: Bleeding
I - PROCEDURE
WARNING
Even
SEE MORE:
K9K, and 764 or 772
IMPORTANT
Wear protective gloves during the operation.
WARNING
Never rotate the engine anti-clockwise (timing end).
WARNING
Do not run the engine without the accessories belt,
to avoid breaking the crankshaft accessories pulley.
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
Parts always to be replace
B-pillar upper trim: Removal - Refitting
C85
REMOVAL
REMOVAL PREPARATION OPERATION
Remove:
the complete rear bench seat,
the rear wing panel lining (see 71A, Body internal
trim, Rear panel lining: Removal - Refitting, 71A-32).
Remove:
the bolt (1),
the seat belt.
Unclip the height adjustment device (2).
Rem
© 2016-2025 Copyright Renault Clio Owners Club
