Renault Clio: Headlight: Removal - Refitting
DISCHARGE LAMPS, and DOCUMENTATION
PHASE 1
IMPORTANT
To prevent eye injuries:
- do not look at a xenon bulb when lit (voltage
when lit 20000 V),
- do not light a bulb which has not been fitted into
its headlight.
IMPORTANT
To prevent burns, wait until the " computers -
power unit " assemblies are cold before removal.
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
DISCHARGE LAMPS, and DOCUMENTATION
PHASE 1
- Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, 80A-1).
- Remove:
- the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
- the front section of the front wheel arch liners (see
Front wheel arch liner: Removal - Refitting)
(55A, Exterior protection),
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
DOCUMENTATION PHASE 1

- Remove the upper bolts (1) from the headlight.

- Remove:
- the headlight lower bolt (2),
- the plastic rivet (3).
DOCUMENTATION PHASE 2

- Remove the upper bolts (4) from the headlight.

- Remove the lower bolts (5) from the headlight.
- Remove the headlight.
- Disconnect the headlight connectors.
- Remove the headlight.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
- Connect the headlight connectors
- Refit the headlight.
II - FINAL OPERATION
DISCHARGE LAMPS, and DOCUMENTATION
PHASE 1
- Connect the battery (see 80A, Battery, Battery: Removal
- Refitting, 80A-1).
- Adjust the headlights (see 80B, Headlights, Headlight:
Adjustment, 80B-9).
- Refit:
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
- the front section of the front wheel arch liners (see
Front wheel arch liner: Removal - Refitting)
(55A, Exterior protection),
- the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
READ NEXT:
DOCUMENTATION PHASE 1
ADJUSTMENT
I - PREPARATION OPERATION FOR CHECK
Place the vehicle in a working area equipped with a
two-post lift.
Note:
Check that the lift is on flat, horizontal ground.
DOCUMENTATION PHASE 1
REMOVAL
DISCHARGE LAMPS
IMPORTANT
To prevent eye injuries:
do not look at a xenon bulb when lit (voltage
when lit 20000 V),
do not light a bulb which has not been fitted into
DOCUMENTATION PHASE 1
DISCHARGE LAMPS
IMPORTANT
To prevent burns, wait until the " computers -
power unit " assemblies are cold before removal.
IMPORTANT
To prevent eye injuries:
do not look at a xe
SEE MORE:
D4F, and 740 or 742 or 764
Petrol vapour rebreathing solenoid
valve
Air inlet pressure sensor
Motorised throttle valve
Injection computer
(5) Fuel injection computer
(6) Motorised throttle valve
(7) Fuel vapour recirculation solenoid
valve
(8) Ignition coil
(9) Upstream oxygen sensor
(1
K4J or K4M
REMOVAL
I - REMOVAL PREPARATION OPERATION
Disconnect the battery (see Battery: Removal - Refitting)
(80A, Battery).
K4M, and 862
Remove:
the air resonator (1).
the air filter unit air inlet pipe (2),
the dipstick,
the dipstick guide bolts (3).
Move aside the dipstick
© 2016-2025 Copyright Renault Clio Owners Club
