Renault Clio: Headlights (changing bulbs)
Direction indicator lights
Turn the bulb holder 1 a quarter of a turn and take out the bulb.
Bulb type: PY24.
Once the bulb has been replaced, check that it is properly secured.
| The engine may be hot
when carrying out operations
in close proximity. In
addition, the engine cooling
fan can come on at any moment. Risk of injury. |
Halogen dipped beam headlight
Remove cover A to access the bulb holder.
To change the bulb:
- remove cover B;
- disconnect wiring 2;
- unclip spring 3 and remove the bulb.
Bulb type: H7
Halogen main beam headlight
To change the bulb:
- remove cover C;
- disconnect wiring 4;
- unclip spring 5 and remove the bulb.
Bulb type: H1
It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights.
Do not touch the bulb glass. Hold it by its base.
When the bulb has been changed, make sure you refit the cover correctly.
| The bulbs are under pressure
and can break when
replaced. Risk of injury. |
Discharge bulb main beam headlights/dipped beam headlights
Never open the cover D.
Bulb type: D5S.
| Due to the danger involved in handling high-voltage devices, this type of bulb must be replaced by an approved dealer. |
| A special mounting is required to fit this type of headlight, it is forbidden to fit a headlight with xenon bulbs to a vehicle which was not designed for it. |
| Any operation on (or modification to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment (harness, components and in particular the alternator). In addition, your Dealer has all the parts required for fitting these units. |
| Before performing any action in the engine compartment, the ignition must be switched off by pressing the engine stop button (please see the information on “Starting, stopping the engine” in Section 2). |
Front side light (depending on the vehicle)
To change a bulb, remove cover A.
Pull bulb holder 6 to access the bulb.
Bulb type: W5W
| The bulbs are under pressure
and can break when
replaced. Risk of injury. |
| To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an approved dealer. |
Daytime running lights 7 (depending on the vehicle)
Please see an authorised dealer.
| The engine may be hot
when carrying out operations
in close proximity. In
addition, the engine cooling
fan can come on at any moment. Risk of injury. |
Daytime running lights and side lights 8 (depending on the vehicle)
Please see an authorised dealer.
Front fog lights 9
The front bumper needs to be removed; consult an approved Dealer.
Bulb type: H16.
Additional lights
If you wish to fit fog lights to your vehicle, please see an authorised dealer.
| Before performing any action in the engine compartment, the ignition must be switched off by pressing the engine stop button (please see the information on “Starting, stopping the engine” in Section 2). |
| Any operation on (or modification to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment (harness, components and in particular the alternator). In addition, your Dealer has all the parts required for fitting these units. |
READ NEXT:
Five-door version
Side lights/brake and direction
indicator lights
Open the boot lid and remove screws 1.
The bulbs are under pressure
and can break when
replaced.
Risk of injury.
To re
Five door and estate versions
Reversing lights and rear fog
lights 12
Open the boot lid.
Unclip cover 13 and remove it.
Turn bulb holder 14 fully anticlockwise
and change the bulb.
To reassemble, proceed in the
SEE MORE:
Front seat: Stripping - Rebuilding
WITHOUT SPORT SEATS, and DOCUMENTATION PHASE 1
IMPORTANT
Before carrying out any work on a safety or proximity
system component, lock the airbag computer
using the Diagnostic tool. When this function is
activated all the ignition lines are disabled and the
airbag warning light on the instrument pan
Front brake disc: Removal - Refitting
EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL SPORT
Brake discs cannot be reground. If there is excessive
scoring or wear, they will need to be replaced (see
30A, General information, Brake: Specifications, 30A-9).
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness inst
