Renault Clio: Gear selection sensor: Removal - Refitting
K9K, and JA5

REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
To remove the gear selection sensor it is essential
that you shift to first gear before removal.
- Remove:
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery),
- the battery tray (see Battery tray: Removal - Refitting)
(MR 392, 80A, Battery),
- the air filter unit (see Air filter unit: Removal - Refitting)
(MR 392, 12A, Fuel mixture).
II - OPERATION FOR REMOVAL OF PART
CONCERNED

- Disconnect the gear selection sensor connector (1).
- Remove:
- the gear selection sensor bolts,
- the gear selection sensor (1).
REFITTING
I - REFITTING PREPARATIONS OPERATION
- Check that the gear selection sensor is able to rotate
freely.
II - REFITTING OPERATION FOR PART
CONCERNED
- Refit:
- the gear selection sensor,
- the gear selection sensor bolts.
- Torque tighten the gear selection sensor bolts (4
Nm).
- Connect the gear selection sensor connector.
III - FINAL OPERATION.
- Refit:
- the air filter unit (see Air filter unit: Removal - Refitting)
(MR 392, 12A, Fuel mixture),
- the battery tray (see Battery tray: Removal - Refitting)
(MR 392, 80A, Battery),
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery),
- Carry out the necessary programming (see Fault
finding - Replacement of components (MR 394,
21B, Sequential gearbox).
D4F, and JA3

REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
To remove the gear selection sensor it is essential
that you shift to first gear before removal.
- Remove:
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery),
- the battery tray (see Battery tray: Removal - Refitting)
(MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART
CONCERNED

- Disconnect the gear selection sensor connector (1).
- Remove:
- the gear selection sensor bolts,
- the gear selection sensor (1).
REFITTING
I - REFITTING PREPARATIONS OPERATION
- Check that the gear selection sensor is able to rotate
freely.
II - REFITTING OPERATION FOR PART
CONCERNED
- Refit:
- the gear selection sensor,
- the gear selection sensor bolts.
- Torque tighten the gear selection sensor bolts (4
Nm).
- Connect the gear selection sensor connector.
III - FINAL OPERATION.
- Refit:
- the battery tray (see Battery tray: Removal - Refitting)
(MR 392, 80A, Battery),
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault
finding - Replacement of components (MR 394,
21B, Sequential gearbox).
READ NEXT:
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Batte
K9K, and JA5
REMOVAL
REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, run co
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
SEE MORE:
DISCHARGE LAMPS, and DOCUMENTATION
PHASE 1
IMPORTANT
To prevent eye injuries:
do not look at a xenon bulb when lit (voltage
when lit 20000 V),
do not light a bulb which has not been fitted into
its headlight.
IMPORTANT
To prevent burns, wait until the " computers -
power unit " assemblies are
K4M - F4R
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
Remove:
the battery (see Battery: Removal - Refitting)
(80A, Battery),
the engine cover,
the battery tray (see Battery tray: Removal - R
© 2016-2025 Copyright Renault Clio Owners Club
