Renault Clio: Camshaft: Removal - Refitting

D4F, and 740 or 742 or 764

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
• Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
• Remove:
  • the air filter unit (see 12A, Fuel mixture, Air filter unit: Removal - Refitting, 12A-17),
  • the intake distributor (see 12A, Fuel mixture, Inlet distributor: Removal - Refitting, 12A-45),
  • the ignition coil (see 17A, Ignition, Coils: Removal - Refitting, 17A-2),
  • the front bumper (see Front bumper: Removal - Refitting) (MR 393, 55A, Exterior protection),
  • the accessories belt (see 11A, Top and front of engine, Accessories belt: Removal - Refitting, 11A-5),
  • the crankshaft accessories pulley (see 11A, Top and front of engine, Crankshaft accessories pulley: Removal - Refitting, 11A-31),
  • the right-hand suspended mounting support (see 19D, Engine mounting, Right-hand suspended engine mounting: Removal - Refitting, 19D-22),
  • the timing belt (see 11A, Top and front of engine, Timing belt: Removal - Refitting, 11A-48),
  • the rocker cover (see 11A, Top and front of engine, Rocker cover: Removal - Refitting, 11A-183).

• Remove:
  • the camshaft pulley mounting bolt using the (Mot.799-01),
  • the camshaft pulley.

• Position the (Mot. 1381) (2).

• Tighten the bolt (3) of the (Mot. 1381).
• Remove the lip seal.

• Remove the camshaft seal cap.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Remove:
  • the camshaft mounting bolts,
  • the camshafts.

• Mark the camshaft bearing caps with an indelible marker pen.

• Remove:
  • the mounting bolts (4) from camshaft bearing cap no. 5,
  • the camshaft bearing caps.

• Remove the camshaft.

REFITTING

I - REFITTING PREPARATION OPERATION

• Apply:
  • two beads (5) of RHODORSEAL 5661 with a width of 2 mm on cylinder head bearing no. 5,
  • two drops (6) of RHODORSEAL 5661 to cylinder head bearing no. 1.
• Apply a blob of oil to the camshaft bearings.

II - REFITTING OPERATION FOR PART CONCERNED

• Refit:
  • the camshaft,
  • the camshaft bearing caps.

• Torque tighten the mounting bolts of camshaft bearing cap no. 5 (9 N.m).

• Refit the camshafts, positioning:
  • the rails in relation to the tappets,
  • the marks (7) on the flywheel end.

• Pretighten in order and to torque the mounting bolts of the camshaft bearing caps (5 N.m).
• Loosen the mounting bolt (1).
• Torque and angle tighten the camshaft bearing cap mounting bolt (7 N.m + 50

  READ NEXT:

   Camshaft seal, timing end: Removal - Refitting

  K9K REMOVAL I - REMOVAL PREPARATION OPERATION Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment). Disconnect the battery (see Battery: Remo

   Oil decanter: Removal - Refitting

  F4R REMOVAL I - REMOVAL PREPARATION OPERATION Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery). Remove: the throttle valve (see 12A, Fuel mixture, Throttle val

   Lifting eyes: Removal - Refitting

  IDENTIFICATION Parts description timing end lifting eye timing end lifting eye mounting bolt gearbox side lifting eye gearbox side lifting eye mounting bolt The lifting eyes and their mount

  SEE MORE:

    Master cylinder - underbody union brake pipe: Removal - Refitting

  LEFT-HAND DRIVE, and WITHOUT ANTI-LOCK BRAKING SYSTEM REMOVAL I - REMOVAL PREPARATION OPERATION Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment). Remove: the engine cover, the engine undertray, the air filter box air inlet pipe,

    Brake servo non-return valve: Removal - Refitting

  LEFT-HAND DRIVE REMOVAL I - REMOVAL PREPARATION OPERATION K4J or K4M or K9K Remove the engine cover. II - OPERATION FOR REMOVAL OF PART CONCERNED Disconnect the non-return valve (1) at the servo. Pull and turn the non-return valve to release it from the rubber sealing washer. K9K Disconn