Renault Clio: Clutch position sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the bolts (1) from the clutch position sensor,
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the clutch position sensor bolt (1),
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
READ NEXT:
Solenoid valve assembly pressure sensor: Removal - Refitting
K9K, and JA5
REMOVAL
REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, run co
Sequential gearbox engine speed sensor: Removal - Refitting
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
Sequential gearbox: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
SEE MORE:
Front pyrotechnic inertia reel: Removal - Refitting
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Airbag
and pretensioners: Precautions for the
repair, 88C-6).
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
To avoid any risk of triggering whe
Rear pyrotechnic inertia reel: Removal - Refitting
B85 or C85 or K85
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Airbag
and pretensioners: Precautions for the
repair, 88C-6).
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
It is essential t
© 2016-2026 Copyright Renault Clio Owners Club - 0.0043
