Renault Clio: Oil pressure sensor: Removal - Refitting

D4F, and 740 or 742 or 764

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Put the vehicle on a two-post lift (see Vehicle: Towing and lifting).
• Disconnect the battery (see Battery: Removal - Refitting).
• Remove the engine undertray.

• Unclip the connector cover (1).
• Remove the oil pressure sensor connector.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Remove the oil pressure sensor.

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

• Refit the oil pressure sensor.
• Torque tighten the oil pressure sensor (32 N.m).

II - FINAL OPERATION.

• Refit the oil pressure sensor connector.
• Clip the connector cover.
• Refit the engine undertray.
• Connect the battery (see Battery: Removal - Refitting).

K9K

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
• Remove the engine undertray.

II - OPERATION FOR REMOVAL OF PART CONCERNED

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

• Refit the oil pressure sensor.
• Torque tighten the oil pressure sensor (40 N.m).
• Connect the oil pressure sensor connector.

II - FINAL OPERATION

• Refit the engine undertray.
• Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Disconnect the battery (see Battery: Removal - Refitting) (80A, Battery).
• Remove the front engine cover.

K4M, and 862

• Remove:
  • the air resonator (1),
  • the air inlet pipe (2) from the air filter unit.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Disconnect:
  • the pinking sensor connector (3),
  • the oil pressure sensor connector (4).
• Remove the oil pressure sensor (5).

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

• Use SURFACE CLEANER (see ) (04B, Consumables - Products) to degrease the bearing face of the oil pressure sensor on the cylinder block.
• Refit the oil pressure sensor.
• Connect:
  • the oil pressure sensor connector,
  • the pinking sensor connector.

II - FINAL OPERATION

K4M, and 862

• Refit:
  • the air filter unit air inlet pipe,
  • the air resonator.
• Refit the engine cover.
• Connect the battery (see Battery: Removal - Refitting) (80A, Battery).

M4R

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
• Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
• Remove:
  • the engine undertray,
  • the front bumper (see Front bumper: Removal - Refitting) (MR 393, 55A, Exterior protection),
  • the frontal impact cross member (see Front impact cross member: Removal - Refitting) (MR 393, 41A, Front lower structure),
  • the front end panel air resonator (see 12A, Fuel mixture, Air resonator: Removal - Refitting, 12A-10).

• Disconnect the oil pressure sensor connector (1).

II - REMOVAL OF PART CONCERNED

• Remove the oil pressure sensor.

REFITTING

I - REFITTING PREPARATIONS OPERATION

• Coat the oil pressure sensor wire with SILICONE ADHESIVE SEALANT (77 11 227 484) to ensure a good seal.

II - REFITTING PART CONCERNED

• Refit the oil pressure sensor.
• Tighten to torque the oil pressure sensor (15 Nm).

III - FINAL OPERATION.

• Connect the oil pressure sensor connector.
• Refit:
  • the front end panel air resonator (see 12A, Fuel mixture, Air resonator: Removal - Refitting, 12A-10),
  • the frontal impact cross member (see Front impact cross member: Removal - Refitting) (MR 393, 41A, Front lower structure),
  • the front bumper (see Front bumper: Removal - Refitting) (MR 393, 55A, Exterior protection),
  • the engine undertray.
• Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).

F4R

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
• Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
• Remove:
  • the front bumper (see Front bumper: Removal - Refitting) (MR 393, 55A, Exterior protection),
  • the frontal impact cross member (see Front impact cross member: Removal - Refitting) (MR 393, 41A, Front lower structure).

• Remove:
  • the plastic cover retaining clips,
  • the plastic cover.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Disconnect the oil pressure sensor connector (3).
• Remove the oil pressure sensor (4).

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

• Refit the oil pressure sensor.
• Torque tighten the oil pressure sensor (30 Nm).
• Connect the oil pressure sensor connector.

II - FINAL REFITTING OPERATION

• Position the plastic cover.
• Refit:
  • the plastic cover retaining clips,
  • the frontal impact cross member (see Front impact cross member: Removal - Refitting) (MR 393, 41A, Front lower structure),
  • the front bumper (see Front bumper: Removal - Refitting) (MR 393, 55A, Exterior protection).
• Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).

D4F, and 784 or 786

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
• Remove the front engine cover.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Disconnect the oil pressure sensor connector (1).
• Remove the oil pressure sensor (2).

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

• Refit the oil pressure sensor.
• Torque tighten the oil pressure sensor (35 Nm).
• Connect the oil pressure sensor connector.

II - FINAL OPERATION.

• Refit the engine undertray.

READ NEXT: