Renault Clio: Clutch position sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the bolts (1) from the clutch position sensor,
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the clutch position sensor bolt (1),
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
READ NEXT:
Solenoid valve assembly pressure sensor: Removal - Refitting
K9K, and JA5
REMOVAL
REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, run co
Sequential gearbox engine speed sensor: Removal - Refitting
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
Sequential gearbox: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
SEE MORE:
Opening Element Sealing
Door sealing film: Removal - Refitting
REMOVAL
Note:
The sealing film can only be used once; it is destroyed
when it is removed.
It is essential to replace the film with a new one
each time it is removed.
REMOVING THE SEALING FILM
Remove the door trim( (see Front side door trim:
Removal - Refitt
Window Sealing
Front side door glass run channel: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
Remove:
the door trim( (see Front side door trim: Removal
- Refitting) (MR 393, 72A, Side opening elements
trim),
the interior weatherstrip,
the door mirror( (see Door mirror: Removal - Refit
© 2016-2026 Copyright Renault Clio Owners Club - 0.0034
