Renault Clio: Gear selection sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Gear selection sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
To remove the gear selection sensor it is essential that you shift to first gear before removal.
- Remove:
- the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery),
- the battery tray (see Battery tray: Removal - Refitting) (MR 392, 80A, Battery),
- the air filter unit (see Air filter unit: Removal - Refitting) (MR 392, 12A, Fuel mixture).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the gear selection sensor connector (1).
- Remove:
- the gear selection sensor bolts,
- the gear selection sensor (1).
REFITTING
I - REFITTING PREPARATIONS OPERATION
- Check that the gear selection sensor is able to rotate freely.
II - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the gear selection sensor,
- the gear selection sensor bolts.
- Torque tighten the gear selection sensor bolts (4 Nm).
- Connect the gear selection sensor connector.
III - FINAL OPERATION.
- Refit:
- the air filter unit (see Air filter unit: Removal - Refitting) (MR 392, 12A, Fuel mixture),
- the battery tray (see Battery tray: Removal - Refitting) (MR 392, 80A, Battery),
- the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery),
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
To remove the gear selection sensor it is essential that you shift to first gear before removal.
- Remove:
- the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery),
- the battery tray (see Battery tray: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the gear selection sensor connector (1).
- Remove:
- the gear selection sensor bolts,
- the gear selection sensor (1).
REFITTING
I - REFITTING PREPARATIONS OPERATION
- Check that the gear selection sensor is able to rotate freely.
II - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the gear selection sensor,
- the gear selection sensor bolts.
- Torque tighten the gear selection sensor bolts (4 Nm).
- Connect the gear selection sensor connector.
III - FINAL OPERATION.
- Refit:
- the battery tray (see Battery tray: Removal - Refitting) (MR 392, 80A, Battery),
- the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
READ NEXT:
Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Batte
Solenoid valve assembly pressure sensor: Removal - Refitting
K9K, and JA5
REMOVAL
REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, run co
Sequential gearbox engine speed sensor: Removal - Refitting
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
SEE MORE:
Trip computer and warning system
Information messages
These can help in the vehicle starting phase, or give information about a
selection or a driving status.
Examples of information messages are given in the following pages.
Examples of messages
Interpreting the display selected
« PARKING BRAKE O
K4M, and DP0
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
IMPORTANT
During this operation, secure the vehicle to the
lift with a strap to prevent it from becoming unbalanced.
To fit the strap to the v
© 2016-2025 Copyright Renault Clio Owners Club
