Renault Clio: Control panel: Removal - Refitting

REMOVAL
I - REMOVAL PREPARATION OPERATION
- Remove the centre console (see Centre console:
Removal - Refitting) (MR 393, 57A, Interior equipment).

- Unclip the trim at (1) and (2) at the base of the dashboard.
RADIO NO. 01 or RADIO NO. 02 or RADIO NO.03
or RADIO NO. 04 or RADIO NO. 05 or RADIO NO.
06
- Remove the radio (see Radio: Removal - Refitting)
(MR 392, 86A, Radio).
NAVIGATION AID 1
- Remove the radio navigation system (see Radio
navigation: Removal - Refitting) (MR 392, 83C,
On-board telematics system).
WITHOUT NAVIGATION AID, and VEHICLE WITHOUT
RADIO
- Unclip the glovebox using the (Car. 1363).

- Unclip the centre trim piece beginning with the upper
section.
- Disconnect the connectors.
II - OPERATION FOR REMOVAL OF PART
CONCERNED

- Remove the mounting bolts (3) from the air conditioning
control panel.
- Move the air conditioning control panel to one side.
CLIMATE CONTROL
- Disconnect the air conditioning control panel connectors.
AIR CONDITIONING or STANDARD HEATING

- Disconnect the connector (4) from the air conditioning
control panel.

- Remove the control panel control cables.
- Disconnect at (5).
- Pull back lug (6).
- Extract the ball joint (7).
- Remove the air conditioning control panel.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
AIR CONDITIONING or STANDARD HEATING

- Refit the control panel control cables.
- Insert the ball joint at (8).
- Clip the sleeve stop at (9).

- Connect the air conditioning control panel connector (10).
CLIMATE CONTROL
- Connect the air conditioning control panel connectors.
- Refit the air conditioning control panel.

- Refit the air conditioning control panel bolts (11).
II - FINAL OPERATION.
- Connect the connectors.
- Clip on the centre trim starting at the top.
RADIO NO. 01 or RADIO NO. 02 or RADIO NO. 03
or RADIO NO. 04 or RADIO NO. 05 or RADIO NO.
06
- Refit the radio (see Radio: Removal - Refitting)
(MR 392, 86A, Radio).
NAVIGATION AID 1
- Refit the radio navigation system (see Radio navigation:
Removal - Refitting) (MR 392, 83C, On-board
telematics system).
WITHOUT NAVIGATION AID, and VEHICLE WITHOUT
RADIO
- Clip the glovebox in position.
- Clip on the dashboard lower trim.
- Refit the centre console (see Centre console: Removal
- Refitting) (MR 393, 57A, Interior equipment).
READ NEXT:
REMOVAL
I - REMOVAL PREPARATION OPERATION
Lock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 394, 88C, Airbags and pretensioners).
Disconnect
REMOVAL
I - REMOVAL PREPARATION OPERATION
Lock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components
(MR 394, 88C, Airbags and pretensioners).
Disconnect t
LEFT-HAND DRIVE
REMOVAL
I - REMOVAL PREPARATION OPERATION
1 - Driver's side
Remove the centre console (see Centre console:
Removal - Refitting) (MR 393, 57A, Interior equipment).
Unclip the da
SEE MORE:
WITHOUT SPORT SEATS, and DOCUMENTATION PHASE 1
IMPORTANT
Before carrying out any work on a safety or proximity
system component, lock the airbag computer
using the Diagnostic tool. When this function is
activated all the ignition lines are disabled and the
airbag warning light on the instrument pan
IMPORTANT
Use a repair bench to ensure the positioning of the
points and the geometry of the axle assemblies.
Note:
The information contained in the following
describes the general repair procedure for all vehicles
having the same design for this part.
Before reading the following general informati
© 2016-2025 Copyright Renault Clio Owners Club
