Renault Clio: Clutch position sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the bolts (1) from the clutch position sensor,
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the clutch position sensor bolt (1),
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
READ NEXT:
Solenoid valve assembly pressure sensor: Removal - Refitting
K9K, and JA5
REMOVAL
REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, run co
Sequential gearbox engine speed sensor: Removal - Refitting
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
Sequential gearbox: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
SEE MORE:
Front wing: General description
Note:
The information contained in the following
describes the general repair procedure for all vehicles
having the same design for this part.
Before reading the following general information,
make sure that there are no special notes associated
with the vehicle. These special notes are specified
i
Exhaust gas recirculation: List and location of components
K9K
K9K, and 764 or 766 or 768 or 772
First fitting of the exhaust gas cooler recirculation
assembly
(1) Exhaust gas recirculation solenoid
valve
(2) Exhaust gas cooler
(3) Exhaust gas inlet pipe
(4) Metal air inlet tube
(5) Cooler support on the flywheel
end
(6) Cooler support on the timing
side
S
© 2016-2025 Copyright Renault Clio Owners Club
