Renault Clio: Engagement sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Engagement sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the engagement sensor connector.
- Remove:
- the engagement sensor bolts,
- the engagement sensor (1).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the engagement sensor,
- the engagement sensor bolts.
- Tighten to torque the engagement sensor bolts (4 Nm).
- Connect the engagement sensor connector.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Refit the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
WARNING
After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the engagement sensor connector.
- Remove:
- the engagement sensor bolts,
- the engagement sensor (1).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the engagement sensor,
- the engagement sensor bolts.
- Tighten to torque the engagement sensor bolts (4 Nm).
- Connect the engagement sensor connector.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Refit the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
WARNING
After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.
READ NEXT:
Actuator module: Removal - Refitting
K9K, and JA5
(1) Clutch solenoid valve
(2) Gear engagement solenoid
valve
(18) Gear engagement solenoid
valve
(4) Selection solenoid valve
(5) Engagement sensor
(20) Gear selection sensor
(7) Solen
Gear selection sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
To remove the gear selection sensor it is essential
that you shift to first gear before removal.
Remove:
the battery (see Battery: R
Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Batte
SEE MORE:
Front bumper wiring: Connector access
FOG LIGHTS
I - LOCATION OF CONNECTORS
R 33 connector (front end panel/front bumper connection).
II - ACCESS TO CONNECTORS
IMPORTANT
Consult the safety and cleanliness advice and
operation recommendations before carrying out
any repair (see 88A, Wiring harness, Wiring:
Precautions for the repair,
Front left-hand wiring: Connector access
I - LOCATION OF CONNECTORS
Connection R 107 (front left-hand wiring/dashboard
wiring connection) composed of two to four connectors
depending on equipment.
R 374 connector (front left-hand wiring/rear left-hand
wiring connection).
Connection R 67 (front left-hand wiring/engine wiring
© 2016-2026 Copyright Renault Clio Owners Club - 0.0036
