Renault Clio: Diesel injection computer: Configuration
Renault Clio III (2005-2013) Service Manual / Engine And Peripherals / Diesel Injection / Diesel injection computer: Configuration
K9K, and 750 or 752 or 764 or 766 or 768
- To configure the computer, (see MR 394 Fault finding, Diesel Injection, Configuration and programming).
Diesel injection computer: Removal - Refitting
K9K
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Remove:
- the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery),
- the battery heat shield,
- the air filter box (see 12A, Fuel mixture, Air filter unit: Removal - Refitting, 12A-17).
II - REMOVAL OF PART CONCERNED
- Disconnect the three connectors (1) from the injection computer.
- Remove:
- the injection computer mounting bolts (2),
- the injection computer (3).
REFITTING
I - REFITTING PART CONCERNED
- Refit the injection computer.
- Torque tighten the injection computer mounting bolts (10 Nm).
II - FINAL OPERATION.
- Connect the injection computer connectors.
- Refit the air filter box (see 12A, Fuel mixture, Air filter unit: Removal - Refitting, 12A-17).
- Refit the battery heat shield,
- Refit the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
Flow regulation solenoid valve: Removal - Refitting
K9K, and 764 or 772
- The flow regulation solenoid valve (1) is integral with the high pressure pump.
- Replace the " high pressure pump - flow regulation solenoid valve " assembly in the event of a fault in the flow regulation solenoid valve (see 13B, Diesel injection, High pressure pump: Removal - Refitting, 13B-23).
Pressure regulation solenoid valve: Removal - Refitting
K9K, and 764 or 772
- The pressure regulation solenoid valve (1) is integral with the high pressure pump.
- Replace the " high pressure pump - pressure solenoid valve " assembly in the event of a fault in the pressure regulation solenoid valve (see 13B, Diesel injection, High pressure pump: Removal - Refitting, 13B-23).
READ NEXT:
High pressure pump leak flow: Check
K9K, and 764 or 772
Disconnect the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery).
Disconnect the inlet pressure sensor (1).
Remove:
the air duct (2) between the air fil
High pressure pump: Removal - Refitting
K9K, and 764 or 772
WARNING
Before starting work on the vehicle, obtain:
a new plug kit (PART NO. 77 01 476 857),
cleaning cloths (PART NO. 77 11 211 707),
cleaning product (PART NO. 77 11 224 18
Flow actuator: Removal - Refitting
K9K, and 750 or 752 or 766 or 768
IMPORTANT
Before carrying out any work on the injection system,
check using the Diagnostic tool :
that the injector rail is not under pressure,
that the fuel temp
SEE MORE:
Hill start assistance
This function assists the driver when
starting on hills. It prevents the vehicle
from rolling backwards, depending on
the slope, by automatically applying the
brakes when the driver lifts his/her foot
off the brake pedal to depress the accelerator
pedal.
System operation
It only operates whe
Speed limiter
The speed limiter function helps you
stay within the driving speed limit that
you choose, known as the limit speed.
Controls
Main “On/Off” switch.
Limit speed activation, storage and
increase switch (+).
Decreasing the limit speed (-).
Activation and recall of memorised
limi
© 2016-2026 Copyright Renault Clio Owners Club - 0.0057
