Renault Clio: Front bumper: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Mechanisms And Accessories / Exterior Protection / Front bumper: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR392, 02, Lifting equipment).
- Remove:
- the lower bolts (1).
- the front parts of the front wheel arch liners (see 55A, Exterior protection, Front wheel arch liner: Removal - Refitting, 55A-41).
- Disconnect the connector (2) (depending on equipment level).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the bolts (3).
- Remove the bolts and clips (4).
- Unclip the side sections of the front bumper.
- Remove the front bumper unit (this operation requires two people).
- Disconnect the headlight washer jet supply (depending on equipment level).
REFITTING
I - REFITTING PREPARATION OPERATION
Note:
During a replacement operation, order the front bumper according to the mark (6) on the front wing of the vehicle:
- tyre size smaller than or equal to 185 = mark on front wing (6) which reads 185,
- tyre size 195 = mark on front wing (6) which reads 195.
- Unclip the trim (5).
- Check the tyre size (6).
II - REFITTING OPERATION FOR PART CONCERNED
- Reconnect the headlight washer jet supply (depending on equipment level).
- Refit the front bumper unit (this operation requires two people).
- Refit the bolts (7).
- Refit the bolts and clips (8).
- Refit the bolts (9).
III - FINAL OPERATION.
- Reconnect the connector (10) (depending on equipment level).
- Test all of the functions with a function test (depending on equipment level).
- Refit the front parts of the front wheel arch liners (see 55A, Exterior protection, Front wheel arch liner: Removal - Refitting, 55A-41).
Front bumper: Conversion
HEADLIGHT WASHERS WITH BLADE
ADAPTATION
Note: When a front bumper is replaced, the replacement part needs to be modified before it is painted so that the headlight washer jets can be fitted.
- Make the conversion using the special tool (part no: 77 11 419 232).
READ NEXT:
Front bumper: Stripping - Rebuilding
EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or
EQUIPMENT LEVEL EA4
or EQUIPMENT LEVEL EA5, and DOCUMENTATION PHASE 1
STRIPPING
I - STRIPPING PREPARATION OPERATION
Remove the f
Rear bumper: Removal - Refitting
EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or
EQUIPMENT LEVEL EA4
or EQUIPMENT LEVEL EA5, and DOCUMENTATION PHASE 1 - EQUIPMENT LEVEL E3 LEISURE
or
EQUIPMENT LEVEL EA1 or EQUI
Aerodynamic diffuser: Removal - Refitting
EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL SPORT
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
II - OPER
SEE MORE:
Replacement parts and repairs
Original parts are based on strict specifications and are subject to highly-specialised
tests. Therefore, they are of at least the same
level of quality as the parts fitted originally.
If you always fit genuine replacement parts to your vehicle, you will ensure
that it performs well. Further
Rear Upper Structure
Rear wing panel: General description
Note:
The information contained in the following
describes the general repair procedure for all vehicles
having the same design for this part.
Before reading the following general information,
make sure that there are no special notes associated
with the vehicle
© 2016-2025 Copyright Renault Clio Owners Club
