Renault Clio: Passenger Compartment Connection Unit

UCH: Removal - Refitting

RIGHT-HAND DRIVE

REMOVAL

I - REMOVAL PREPARATION OPERATION

• If replacing the UCH, carry out the necessary programming using the Diagnostic tool. (see Fault finding - Replacement of components) (MR 394, 87B, Passenger compartment connection unit).
• Disconnect the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1).
• Remove the storage compartment (see Glovebox: Removal - Refitting) (MR 393, 57A, Interior equipment).

• Unclip the connectors from the beam.

• Unclip the connector mountings on the beam at (2),
• Remove the connector mountings at (3).

II - OPERATION FOR REMOVAL OF PART CONCERNED

VEHICLE WITH KEY

• Unclip the connectors.

• Remove the bolt (4).

• Unclip the rear section of the UCH by pressing on the lugs (5) with a small flat-blade screwdriver.

• Remove the UCH at (6), (7).

• Unclip the UCH from its mounting.

VEHICLE WITH CARD

• Unclip the first row of connectors.
• Remove the bolt (8).

• Unclip the second row of connectors (9).

• Remove the UCH (10), (11).

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

VEHICLE WITH KEY

• Fit the front section of the UCH,
• Clip the rear section of the UCH,
• Tighten the bolt (4),
• Clip the connectors in place.

VEHICLE WITH CARD

• Fit the UCH,
• Tighten the bolt (8),
• Clip the connectors in place.

II - FINAL OPERATION.

• Clip:
  • the connector mountings on the beam,
  • the connectors.
• Refit the storage compartment (see Glovebox: Removal - Refitting) (MR 393, 57A, Interior equipment).
• Connect the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1).
• If replacing the UCH, carry out the necessary programming using the Diagnostic tool. (see Fault finding - Replacement of components) (MR 394, 87B, Passenger compartment connection unit).

LEFT-HAND DRIVE

REMOVAL

I - REMOVAL PREPARATION OPERATION

• When replacing the UCH, carry out the necessary operations using the Diagnostic tool (see Fault finding - Replacement of components) (MR 394, 87B, Passenger compartment connection unit).
• Disconnect the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1).

• Unclip the moulding at (1).

• Remove:
  • the plastic rivet (2),
  • bolt (3).

• Remove the door seal,
• Remove the dashboard side face (4).

• Remove:
  • the bolt (5),
  • the dashboard lower trim (6).

• Remove the dashboard trim (7) while unclipping the connectors.

• Unclip the connectors on the beam (9).

• Unclip the connector mountings on the beam at (10)

• Remove the connector mountings at (11).

II - REMOVAL STAGE FOR THE PART CONCERNED.

VEHICLE WITH KEY

• Unclip the connectors.

• Remove the bolt (12).

• Unclip the rear section of the UCH by pressing on the lugs (13) with a small flat-blade screwdriver.

• Remove the UCH at (14), (15).

• Unclip the UCH from its mounting.

VEHICLE WITH CARD

• Unclip the first row of connectors,
• Remove the bolt (16).

• Unclip the second row of connectors.

• Remove the UCH (17), (18).

REFITTING

I - REFITTING STAGE FOR THE PART CONCERNED.

VEHICLE WITH KEY

• Fit the front section of the UCH,
• Clip the rear section of the UCH,
• Tighten the bolt (12),
• Clip the connectors in place.

VEHICLE WITH CARD

• Fit the UCH,
• Tighten the bolt (16),

II - FINAL OPERATION.

• Clip:
  • the connector mountings on the beam,
  • the connectors on the beam,
  • the dashboard trim.
• Tighten the bolts (3), (5),
• Clip:
  • the plastic rivet,
  • the dashboard side panel,
  • the dashboard moulding,
  • the door seal,
  • the dashboard lower trim (6).
• Connect the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1).
• If replacing the UCH, carry out the necessary programming using the Diagnostic tool. (see Fault finding - Replacement of components) (MR 394, 87B, Passenger compartment connection unit).

READ NEXT: