Renault Clio: Parking brake cables: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Chassis / Mechanical Component Controls / Parking brake cables: Removal - Refitting
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Remove the centre console (see Centre console: Removal - Refitting) (MR 393, 57A, Interior equipment).
DRUM BRAKE
- Remove:
- the wheels (see 35A, Wheels and tyres, Wheel: Removal - Refitting, 35A-1),
- the drums (see 33A, Rear axle components, Rear brake drum: Removal - Refitting, 33A-19).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Loosen the adjusting nut (1) for the parking brake cables enough to be able to remove the parking brake cables.
- Remove the parking brake cables (2) at the control lever.
- Unclip the sheath (3) from its stop on the bodywork using a pair of pliers.
DRUM BRAKE
- Remove the parking brake cable (4) from the lever (5) using pliers and a screwdriver.
- Unclip the parking brake cable sheath (6) from the drum back-plate.
DISC BRAKE
- Remove the parking brake cables (7) at the brake callipers.
- Unclip the parking brake cables from their guides (8).
- Remove the parking brake cables:
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit the parking brake cables.
- Hook the parking brake cables onto their guides.
DRUM BRAKE
- Reattach the parking brake cable sheath onto the drum back-plate.
- Refit the parking brake cable back into the lever housing using a pair of pliers and a screwdriver.
- Check that the cables (9) are correctly positioned on the levers.
DISC BRAKE
- Refit the parking brake cables at the brake callipers.
- Reattach the sheath stop to the bodywork (3).
- Refit the parking brake cables at the control lever.
- Adjust the parking brake cables (see 37A, Mechanical component controls, Parking brake lever: Adjustment, 37A-90).
II - FINAL OPERATION.
DRUM BRAKE
- Refit:
- the drums (see 33A, Rear axle components, Rear brake drum: Removal - Refitting, 33A-19),
- the wheels (see 35A, Wheels and tyres, Wheel: Removal - Refitting, 35A-1)
- Refit the centre console (see Centre console: Removal - Refitting) (MR 393, 57A, Interior equipment).
READ NEXT:
Brake servo: Check
RIGHT-HAND DRIVE
There is no "RENAULT" tool to check the braking assistance
circuit.
Use a vacuum pump fitted with couplings, part numbers
7701349942 and 7700105874 with hose part
number 8200027352
Hydraulic unit without ESP: Removal - Refitting
LEFT-HAND DRIVE
WARNING
Prepare for the flow of fluid, and protect the surrounding
components.
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towin
SEE MORE:
Tyre pressure
Label A
Open the driver’s door to read it.
Tyre pressures should be checked
when the tyres are cold.
If the tyre pressures cannot be checked
when the tyres are cold, increase the
pressures from 0.2 to 0.3 bar (or 3 PSI).
Never deflate a hot tyre.
Vehicle fitted with a tyre pressu
Mixing motor: Removal - Refitting
LEFT-HAND DRIVE, and CLIMATE CONTROL
REMOVAL
I - REMOVAL PREPARATION OPERATION
Remove the centre console (see Centre console:
Removal - Refitting) (MR 393, 57A, Interior equipment).
Unclip the trim at (1) and (2) at the base of the dashboard.
Partially remove seal (3).
Remove the sid
© 2016-2025 Copyright Renault Clio Owners Club
