Renault Clio: Clutch position sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the bolts (1) from the clutch position sensor,
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the engine undertray.
- Disconnect the clutch position sensor connector.
- Remove:
- the clutch position sensor bolt (1),
- the clutch position sensor (2).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the clutch position sensor,
- the clutch position sensor bolts.
- Connect the clutch position sensor connector.
II - FINAL OPERATION.
- Refit the engine undertray.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components (MR 394, 21B, Sequential gearbox).
READ NEXT:
Solenoid valve assembly pressure sensor: Removal - Refitting
K9K, and JA5
REMOVAL
REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, run co
Sequential gearbox engine speed sensor: Removal - Refitting
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
Sequential gearbox: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
Before any operation on the sequential system,
discharge the accumulator using the Diagnostic
tool.
To discharge the accumulator, ru
SEE MORE:
Diesel return pipe: Removal - Refitting
K9K, and 764 or 772
IMPORTANT
Consult the safety instructions and cleanliness
advice and the operation recommendations before
carrying out any repairs (see Diesel injection:
Repair precautions).
IMPORTANT
Before carrying out any work on the injection system,
check using the Diagnostic tool :
that
Clutch circuit: Removal - Refitting
JH3 or JR5
Note:
Each time an operation is carried out on the
hydraulic clutch system, bleed the circuit:
between the reservoir and the bleed hole,
between the bleed hole and the clutch release
bearing.
REMOVAL
I - REMOVAL PREPARATION OPERATION
K4J or K4M
Remove the resonator.
Remov
© 2016-2025 Copyright Renault Clio Owners Club
