Renault Clio: Sequential gearbox gear lever: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Sequential gearbox gear lever: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the gear lever cover (1) using a screwdriver.
- Disconnect the gear lever lighting connector (2).
- Remove:
- the rear bolts (3) from the centre console,
- the front bolts (4) from the centre console.
- Remove the soundproofing (5) from the gear lever.
- Detach the connector (6) from the gear lever.
- Disconnect the gear lever connector.
- Remove:
- the bolts (7) from the gear lever base plate,
- the gear lever.
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the gear lever,
- the gear lever base plate bolts,
- Connect the gear lever connector.
- Attach the gear lever connector.
- Refit:
- the gear lever soundproofing,
- the front bolts to the centre console,
- the rear bolts to the centre console.
- Connect the gear lever lighting connector.
- Refit the gear lever cover.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Remove the gear lever cover (1) using a screwdriver.
- Disconnect the gear lever lighting connector (2).
- Remove:
- the rear bolts (3) from the centre console,
- the front bolts (4) from the centre console.
- Remove the soundproofing (5) from the gear lever.
- Detach the connector (6) from the gear lever.
- Disconnect the gear lever connector.
- Remove:
- the bolts (7) from the gear lever base plate,
- the gear lever.
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the gear lever,
- the gear lever base plate bolts,
- Connect the gear lever connector.
- Attach the gear lever connector.
- Refit:
- the gear lever soundproofing,
- the front bolts to the centre console,
- the rear bolts to the centre console.
- Connect the gear lever lighting connector.
- Refit the gear lever cover.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
READ NEXT:
Sequential gearbox oil: Specifications
5-SPEED MANUAL SEQUENTIAL GEARBOX
I - GEARBOX TYPE/OIL TYPE CORRELATIONS:
II - STANDARDS AND PART NUMBERS OF THE
VARIOUS RECOMMENDED OILS:
Sequential gearbox: Bleeding
I - PROCEDURE
WARNING
Even
Automatic gearbox: Identification
DP0
The automatic transmission series number can be
found in two places: on a label on the hydraulic distributor
cover (1) and etched onto the outer casing (2) on
the wheel side.
Automatic gearbox oi
SEE MORE:
Filler neck: Removal - Refitting
D4F or F4R or K4J or K4M or K9K or M4R
IMPORTANT
During this operation, be sure to:
be careful of fuel splashes when disconnecting the
union.
IMPORTANT
Wear goggles with side protectors for this operation.
IMPORTANT
Wear latex gloves during the operation.
WARNING
To prevent impurities from ente
Engine cooling system: Check
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpectedly
(risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
do not open the expansion bottle cap,
do not drain the cooling system,
do not open the bleed screw(s).
N
© 2016-2025 Copyright Renault Clio Owners Club
