Renault Clio: Engine wiring: Connector access
Renault Clio III (2005-2013) Service Manual / Electrical Equipment / Wiring Harness / Engine wiring: Connector access
I - LOCATION OF CONNECTORS
- R 67 connector (Engine wiring harness/front left-hand wiring connection).
- Depending on the engine, connection R 67 is composed of three or four connectors.
K4J or K4M
- R 37 connector (Engine wiring harness/injection connection).
D4F
- R 37 connector (Engine wiring harness/injection connection).
- R 235 connector (Automatic transmission wiring/ dashboard wiring connection).
F4R
- R 37 connector (Engine wiring harness/injection connection).
M4R
- R 20 connector (Engine wiring harness/injection connection).
- R 24 connector (Engine wiring harness/injection connection).
II - ACCESS TO CONNECTORS
IMPORTANT
Consult the safety and cleanliness advice and operation recommendations before carrying out any repair (see 88A, Wiring harness, Wiring: Precautions for the repair, 88A-5).
WARNING
To prevent damaging the connectors, consult the disconnection procedure (see Connector: Disconnection and reconnection) (Technical Note 6015A, 88A, Wiring).
- Switch off the ignition.
- Disconnect the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1)
1 - Access to the R 67 connectors
- Remove:
- the bolts (1),
- the Protection and Switching Unit cover.
- Disconnect the R 67 connectors.
2 - Access to the R 37 connector
K4J or K4M
- Remove the front engine cover.
- Disconnect the R 37 connector.
D4F
- Remove the air filter box (see Air filter unit: Removal - Refitting) (MR 392, 12A, Fuel mixture).
- Disconnect the R 37 connector.
F4R
- Disconnect the R 37 connector.
3 - Access to the R 235 connector
D4F
- Remove:
- the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1),
- the battery tray bracket (see 80A, Battery, Battery tray: Removal - Refitting, 80A-5).
- Disconnect the R 235 connector.
4 - Access to the R 20 and R 24 connectors
M4R
- Remove the front engine cover.
- Disconnect the R 20 and R 24 connectors.
READ NEXT:
K4J or K4M
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precautions
for the repair, 88A-5).
WARNING
To preve
K9K
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precautions
for the repair, 88A-5).
WARNING
To preve
SEE MORE:
Transporting objects in the boot
Always position the objects transported
so that the largest surface is against:
The rear bench seatback for normal
loads (example A).
The front seatbacks with the rear
seatbacks folded down, as is the case
for maximum loads (example B).
If you have to place objects on the
Aerodynamic diffuser: Removal - Refitting
EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL SPORT
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Remove:
the nuts (1),
the bolts (2).
Unclip the a
© 2016-2025 Copyright Renault Clio Owners Club
