Renault Clio: Underbody heights: Adjustment value

I - MEASURING POINTS

Renault Clio. Underbody heights: Adjustment value

Radius under load:

1 - Front height (W1)

Renault Clio. Underbody heights: Adjustment value

Renault Clio. Underbody heights: Adjustment value

(W1) : Height between the ground and the rear cross member bolt head

2 - Rear height (W2)

Renault Clio. Underbody heights: Adjustment value

Renault Clio. Underbody heights: Adjustment value

(W2) : Height between the ground and the shaft of the rubber bush on the bearing

II - MEASURING PROCEDURE

Note: For measurements (W1) and (W2), take into account the height difference between the plates and the lift.

Measure the heights:

Note: The value of Wx to be entered into the geometry bench is the average of the W1 heights, right-hand and left-hand and of the W2 heights, right-hand and left-hand.

Note: If the measuring points are located in empty space (between the rails of the lift), use a bar.

1 - Plate higher than the lift:

Renault Clio. Underbody heights: Adjustment value

Measure the heights (1), (2), (3).
Example: (1) = 13 cm, (2) = 8 cm, (3) = 10 cm.
Calculate the height Wx:
Wx = height (1) + height (3) - height (2)
Wx = 15 cm

2 - Plate lower than the lift:

Renault Clio. Underbody heights: Adjustment value

Measure the heights (1), (2), (3).
Example: (1) = 8 cm, (2) = 10 cm, (3) = 4 cm.
Calculate the height Wx:
Wx = height (1) + height (2) + height (3)
Wx = 22 cm

III - VEHICLE IN RUNNING ORDER POSITION

VODM (Vehicle in working order) position:

EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT LEVEL EAG

(W1) = 171 +- 13 mm
(W2) = 259 +- 16 mm

EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL SPORT, and WITHOUT ADDITIONAL PACK

(W1) = 156 +- 5 mm
(W2) = 257 +- 16 mm

EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL SPORT, and ADDITIONAL EXTREME PACK

(W1) = 148+7
-14mm
(W2) = 249+ 9
-16mm

Note:

The position of the vehicle varies according to:

READ NEXT:

 Front axle system: Tightening torque

EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT LEVEL EAG EQUIPMENT LEVEL EAC or EQUIPMENT

 Rear axle system: Tightening torque

Rear axle assembly: Adjustment values EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2 or EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT LE

 Rigid brake pipe: Repair

This procedure applies to copper pipes diameter 4.7 mm. Note: This procedure does not apply to: hybrid pipes (pipe + hose), pipes with diameters 6 mm and 8 mm. REPAIR I - PIPE PREPARATION OPERATI

SEE MORE:

 Crankshaft accessories pulley: Removal - Refitting

D4F, and 740 or 742 or 764 REMOVAL I - REMOVAL PREPARATION OPERATION Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment). Remove: the front right-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres), the front r

 Front right-hand driveshaft gaiter, gearbox side: Removal - Refitting

DP0 or JH3 or JR5 or TL4 Deflector Propeller shaft Driveshaft yoke sleeve Spider RC gaiter Tightening clip Lock ring Tightening ring REMOVAL I - REMOVAL PREPARATION OPERATION Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment). Di

© 2016-2025 Copyright Renault Clio Owners Club