Renault Clio: Sequential gearbox: Removal - Refitting

K9K, and JA5

Renault Clio. Sequential gearbox

REMOVAL

I - REMOVAL PREPARATION OPERATION

IMPORTANT

Before any operation on the sequential system, discharge the accumulator using the Diagnostic tool.

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

II - OPERATION FOR REMOVAL OF PART CONCERNED

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

REFITTING

I - REFITTING PREPARATION OPERATION

Renault Clio. Sequential gearbox

WARNING

To avoid damaging the slave cylinder, do not coat the gearbox output shaft with grease.

WARNING

To prevent leaks, replace the slave cylinder after replacing the clutch pressure plate.

Note:

II - REFITTING OPERATION FOR PART CONCERNED

III - FINAL OPERATION

WARNING

After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.

D4F, and JA3

Renault Clio. Sequential gearbox

REMOVAL

I - REMOVAL PREPARATION OPERATION

IMPORTANT

Before any operation on the sequential system, discharge the accumulator using the Diagnostic tool.

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

II - OPERATION FOR REMOVAL OF PART CONCERNED

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

Renault Clio. Sequential gearbox

REFITTING

I - REFITTING PREPARATION OPERATION

Renault Clio. Sequential gearbox

WARNING

To avoid damaging the slave cylinder, do not coat the gearbox output shaft with grease.

WARNING

To prevent leaks, replace the slave cylinder after replacing the clutch pressure plate.

Note:

II - REFITTING OPERATION FOR PART CONCERNED

III - FINAL OPERATION

WARNING

After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.

READ NEXT:

 Sequential gearbox converter: Removal - Refitting

K9K, and JA5 REMOVAL I - REMOVAL PREPARATION OPERATION Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment). Disconnect the battery (see Batte

 Sequential gearbox gear lever: Removal - Refitting

K9K, and JA5 REMOVAL I - REMOVAL PREPARATION OPERATION Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery). II - OPERATION FOR REMOVAL OF PART CONCERNED Remove the

 Sequential gearbox oil: Specifications

5-SPEED MANUAL SEQUENTIAL GEARBOX I - GEARBOX TYPE/OIL TYPE CORRELATIONS: II - STANDARDS AND PART NUMBERS OF THE VARIOUS RECOMMENDED OILS: Sequential gearbox: Bleeding I - PROCEDURE WARNING Even

SEE MORE:

 Exhaust gas recirculation: List and location of components

K9K K9K, and 764 or 766 or 768 or 772 First fitting of the exhaust gas cooler recirculation assembly (1) Exhaust gas recirculation solenoid valve (2) Exhaust gas cooler (3) Exhaust gas inlet pipe (4) Metal air inlet tube (5) Cooler support on the flywheel end (6) Cooler support on the timing side S

 Speed sensor: Removal - Refitting

DP0 Do not drain or remove the automatic gearbox in order to remove the speed sensor. The output speed sensor has been deleted and replaced with wheel speed sensors. REMOVAL I - REMOVAL PREPARATION OPERATION Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A,

© 2016-2025 Copyright Renault Clio Owners Club