Renault Clio: Recirculation control cable: Removal - Refitting

Renault Clio III (2005-2013) Service Manual / Air Conditioning / Heating / Recirculation control cable: Removal - Refitting

LEFT-HAND DRIVE, and AIR CONDITIONING or STANDARD HEATING

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Partially remove seal (1).

• Remove the side panel (2).

• Remove the bolt (3) from the base of the dashboard.
• Unclip the trim piece (4) from the driver's side dashboard lower cover.

• Remove the bolts (5) from the lower cover.
• Remove the lower cover (6).
• Disconnect the connectors (depending on equipment level).
• Remove the centre console (see Centre console: Removal - Refitting) (MR 393, 57A, Interior equipment).

• Unclip the trim at (7) and (8) at the base of the dashboard.

RADIO NO. 01 or RADIO NO. 02 or RADIO NO.03 or RADIO NO. 04 or RADIO NO. 05 or RADIO NO. 06

• Remove the radio (see Radio: Removal - Refitting) (MR 392, 86A, Radio).

NAVIGATION AID 1

• Remove the radio navigation system (see Radio navigation: Removal - Refitting) (MR 392, 83C, On-board telematics system).

WITHOUT NAVIGATION AID, and VEHICLE WITHOUT RADIO

• Unclip the glovebox using the (Car. 1363).

• Unclip the centre trim piece beginning with the upper section.
• Disconnect the connectors.

• Remove the air conditioning control panel bolts (9).
• Move the air conditioning control panel away from the dashboard.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Remove the air recirculation control cable from the control panel.
• Disconnect at (10).
• Remove the bracket (11).
• Extract the ball joint (12).

• Unclip the cable sleeve stop (13) from the distribution unit.
• Remove:
  • the ball joint on the air recirculation flap (14),
  • the air recirculation control cable.

Note: Note the route of the air recirculation control cable.

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

• Refit the air recirculation control cable.
• Refit the ball joint on the air recirculation flap (16).
• Clip the cable sleeve stop (15) onto the distribution unit.

• Refit the air recirculation control cable on the control panel.
• Clip the sleeve stop at (17).
• Refit the ball joint (18).

II - FINAL OPERATION.

• Position the air conditioning control panel on the dashboard.
• Refit the air conditioning control panel bolts (19).
• Connect the central trim connectors.
• Clip in the centre trim piece beginning with the lower section.

RADIO NO. 01 or RADIO NO. 02 or RADIO NO. 03 or RADIO NO. 04 or RADIO NO. 05 or RADIO NO. 06

• Refit the radio (see Radio: Removal - Refitting) (MR 392, 86A, Radio).

NAVIGATION AID 1

• Refit the radio navigation system (see Radio navigation: Removal - Refitting) (MR 392, 83C, On-board
   telematics system).

WITHOUT NAVIGATION AID, and VEHICLE WITHOUT RADIO

• Clip on the glovebox.

• Clip on the dashboard lower trim.
• Refit the centre console (see Centre console: Removal - Refitting) (MR 393, 57A, Interior equipment).
• Refit:
  • the lower cover,
  • the lower cover bolts,
  • the bolts to the base of the dashboard.
• Clip on the driver's side dashboard lower cover trim piece.
• Refit:
  • the side panel,
  • the seal.

RIGHT-HAND DRIVE, and AIR CONDITIONING or STANDARD HEATING

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Remove:
  • the glovebox (see Glovebox: Removal - Refitting) (MR 393, 57A, Interior equipment),
  • the centre console (see Centre console: Removal - Refitting) (MR 393, 57A, Interior equipment).

• Unclip the trim at (1) and (2) at the base of the dashboard.

WITHOUT NAVIGATION AID, and RADIO NO. 01 or RADIO NO. 02 or RADIO NO. 03 or RADIO NO. 04 or RADIO NO. 05 or RADIO NO. 06

• Remove the radio (see Radio: Removal - Refitting) (MR 392, 86A, Radio).

NAVIGATION AID 1

• Remove the radio navigation system (see Radio navigation: Removal - Refitting) (MR 392, 83C, On-board telematics system).

WITHOUT NAVIGATION AID, and VEHICLE WITHOUT RADIO

• Unclip the glovebox using the (Car. 1363).

• Unclip the centre trim piece beginning with the upper section.
• Disconnect the connectors.

• Remove the air conditioning control panel bolts (3).
• Move the air conditioning control panel away from the dashboard.

II - OPERATION FOR REMOVAL OF PART CONCERNED

• Remove the air recirculation control cable from the control panel.
• Disconnect at (4).
• Remove the bracket (5).
• Extract the ball joint (6).

• Unclip the cable sleeve stop (7) from the distribution unit.
• Remove:
  • the ball joint on the air recirculation flap (8),
  • the air recirculation control cable.

Note: Note the route of the air recirculation control cable.

REFITTING

I - REFITTING OPERATION FOR PART CONCERNED

• Refit the ball joint on the air recirculation flap (10).
• Clip the cable sleeve stop (9) onto the distribution unit.

• Refit the air recirculation control cable for the control panel.
• Refit the ball joint (12).
• Clip the sleeve stop at (11).

II - FINAL OPERATION.

• Position the air conditioning control panel on the dashboard.
• Refit the air conditioning control panel bolts (13).
• Connect the central trim connectors.
• Clip in the centre trim piece beginning with the lower section.

WITHOUT NAVIGATION AID, and RADIO NO. 01 or RADIO NO. 02 or RADIO NO. 03 or RADIO NO. 04 or RADIO NO. 05 or RADIO NO. 06

• Refit the radio (see Radio: Removal - Refitting) (MR 392, 86A, Radio).

NAVIGATION AID 1

• Refit the radio navigation system (see Radio navigation: Removal - Refitting) (MR 392, 83C, On-board
   telematics system).

WITHOUT NAVIGATION AID, and VEHICLE WITHOUT RADIO

• Clip the glovebox in position.

• Clip on the dashboard lower trim.
• Refit:
  • the centre console (see Centre console: Removal - Refitting) (MR 393, 57A, Interior equipment),
  • the glovebox (see Glovebox: Removal - Refitting) (MR 393, 57A, Interior equipment),

READ NEXT: