Renault Clio: Rear bumper wiring: Connector access
I - LOCATION OF CONNECTORS
- R 319 connecter (rear bumper/rear connection).
II - ACCESS TO CONNECTORS
IMPORTANT
Consult the safety and cleanliness advice and
operation recommendations before carrying out
any repair (see 88A, Wiring harness, Wiring:
Precautions for the repair, 88A-5).
WARNING
To prevent damaging the connectors, consult the
disconnection procedure (see Connector: Disconnection
and reconnection) (Technical Note
6015A, 88A, Wiring).
- Switch off the ignition.
- Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, 80A-1).
- Remove the light on the rear left-hand wing (see
81A, Rear lighting, Rear wing light: Removal -
Refitting, 81A-5).
- Disconnect the R 319 connector.
Rear bumper wiring: Removal - Refitting
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precautions
for the repair, 88A-5).
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
- Switch off the ignition.
- Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, 80A-1).
- Remove
- the rear wheel arch liners (see Rear wheel arch
liner: Removal - Refitting) (MR 393, 55A, Exterior
protection),
- the rear lights on the wing (see 81A, Rear lighting,
Rear wing light: Removal - Refitting, 81A- 5),
- Disconnect the R 319 connector.
- Remove the rear bumper (see Rear bumper: Removal
- Refitting) (MR 393, 55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
WARNING
To prevent any risk of noise, premature wear,
short circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.
- Disconnect the connector (3) from the number plate lights (1).
REAR PROXIMITY RADAR
- Disconnect the connector (4) from the rear proximity sensors (2).
- Unclip the rear bumper wiring.
- Remove the rear bumper wiring.
WARNING
To prevent any damage during the removal operation,
check that the wiring is free from its mountings
(retaining clip, plastic clip, adhesive tape,
connector, etc.).
REFITTING
I - REFITTING PREPARATION OPERATION
- If replacing with more wiring, lock the unused connectors
(see Connectors: Sealing and immobilisation)
(Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
- Connect the number plate light connectors.
REAR PROXIMITY RADAR
- Connect the proximity radar connectors.
- Clip the wiring onto the rear bumper.
WARNING
To prevent damage to the wiring harness when
refitting, observe the original routing.
III - FINAL OPERATION.
- Refit the rear bumper (see Rear bumper: Removal
- Refitting) (MR 393, 55A, Exterior protection).
- Connect the R319 connector.
- Refit:
- the rear lights on the wing (see 81A, Rear lighting,
Rear wing light: Removal - Refitting, 81A- 5),
- the rear wheel arch liners (see Rear wheel arch
liner: Removal - Refitting) (MR 393, 55A, Exterior
protection).
- Connect the battery (see 80A, Battery, Battery: Removal
- Refitting, 80A-1).
READ NEXT:
I - LISTS OF COMPONENTS
list of components
Driver and passenger front airbags (1).
C85 or S85
Anti-submarining airbags located in the base of the front seats (2).
B85 or K85
Front buckle pretensioner
I - PRECAUTIONS FOR REPAIR
IMPORTANT
All operations on airbag and pretensioner systems
must be carried out by qualified trained personnel.
The airbags have a pyrotechnic gas generator, with
an ignit
SEE MORE:
EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL EA2
or EQUIPMENT
LEVEL EA3 or EQUIPMENT LEVEL EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT LEVEL EAG
WARNING
Do not use the lower arm for support with a lifting
system.
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle
Heated seat pad: Removal - Refitting
WITHOUT SPORT SEATS, and DOCUMENTATION PHASE 1
REMOVAL
I - REMOVAL PREPARATION OPERATION
Remove:
the front seat (see 75A, Front seat frames and
mechanisms, Complete front seat: Removal -
Refitting, 75A-33),
the seat base trim (see 77A, Front seat trim,
© 2016-2024 Copyright Renault Clio Owners Club