Renault Clio: Driver's front side door wiring: Removal - Refitting

IMPORTANT

Consult the safety and cleanliness advice and operation recommendations before carrying out any repair (see 88A, Wiring harness, Wiring: Precautions for the repair, 88A-5).

REMOVAL

I - REMOVAL PREPARATION OPERATION

• Raise the window fully.
• Switch off the ignition.
• Disconnect the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1).

WARNING

To avoid damaging the connectors, consult the disconnection procedures (see Connector: Disconnection and reconnection) (Technical Note 6015A, 88A, Wiring).

• Remove the front speaker (see 86A, Radio, Front speakers: Removal - Refitting, 86A-14).

LEFT-HAND DRIVE, and DOOR MIRRORS 02 or DOOR MIRRORS 03

• Remove the door mirror (see Door mirror: Removal - Refitting) (MR 393, 56A, Exterior equipment),

RIGHT-HAND DRIVE

• Remove the door mirror (see Door mirror: Removal - Refitting) (MR 393, 56A, Exterior equipment),

• Remove:
  • the side door trim (see Front side door trim: Removal - Refitting) (MR 393, 72A, Side opening element trim),
  • the door sealing film (see Door sealing film: Removal - Refitting) (MR 393, 65A, Opening element sealing),
  • the side indicator.

• Remove the three door lock bolts (1).

II - REMOVAL OF PART CONCERNED

WARNING

To prevent any risk of noise, premature wear, short circuits, etc. after the refitting operation, mark the wiring routing and how to connect the connectors.

• Disconnect the door lock connector (2).

VEHICLE WITH CARD

• Disconnect the presence detector connector (3).
• Disconnect the opening aerial connector (4).

ELECTRIC FRONT WINDOW or ONE-TOUCH ELECTRIC FRONT WINDOW or PASSENGER ELECTRIC ONE-TOUCH WINDOW CONTROL

• Remove clip (6).
• Disconnect the electric window motor connector (7).

• Remove:
  • The three bolts (8) of the front offset frame (9).
  • The front offset frame (9), by lowering it, then pivoting it and removing it through the speaker mounting hole.

• Remove the clips (10) and (11).
• Disconnect the door connector (12).
• Remove all of the clips (5) using a pair of unclipping pliers.

WARNING

To prevent any damage during the removal operation, check that the wiring is free from its mountings (retaining clip, plastic clip, adhesive tape, connector, etc.).

• Remove the wiring.

REFITTING

I - REFITTING PREPARATION OPERATION

• If replacing with more complete wiring, immobilise the unused connectors (see Connector: Sealing and locking) (Technical Note 6015A, 88A, Wiring).

II - REFITTING PART CONCERNED

• Refit the wiring, respecting the original routing.
• Clip all the clips into place (5).
• Refit:
  • The front offset frame.
  • The three bolts of the front offset frame.

ELECTRIC FRONT WINDOW or ONE-TOUCH ELECTRIC FRONT WINDOW or PASSENGER ELECTRIC ONE-TOUCH WINDOW CONTROL

• Clip on the clip (6).
• Connect the electric window motor connector.

VEHICLE WITH CARD

• Connect the opening aerial connector.
• Connect the presence sensor connector.

• Connect the tailgate lock connector.
• Connect the door connector (12).
• Clip on the clips (11) and (10).
• Refit:
  • the three door lock bolts,
  • the side indicator,
  • the door sealing film (see Door sealing film: Removal - Refitting) (MR 393, 65A, Opening element sealing),
  • the side door trim (see Front side door trim: Removal - Refitting) (MR 393, 72A, Side opening element trim).

RIGHT-HAND DRIVE

• Refit the door mirror (see Door mirror: Removal - Refitting) (MR 393, 56A, Exterior equipment).

LEFT-HAND DRIVE, and DOOR MIRRORS 02 or DOOR MIRRORS 03

• Refit the door mirror (see Door mirror: Removal - Refitting) (MR 393, 56A, Exterior equipment).

• Refit the front speaker (see 86A, Radio, Front speakers: Removal - Refitting, 86A-14).
• Connect the battery (see 80A, Battery, Battery: Removal - Refitting, 80A-1).

READ NEXT: