Renault Clio: Master cylinder - front left-hand calliper brake pipe: Removal - Refitting
LEFT-HAND DRIVE, and WITHOUT ANTI-LOCK BRAKING SYSTEM

REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
- Remove:
- the engine cover,
- the engine undertray,
- the air filter box air inlet pipe,
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery),
- the battery protective shield (see Battery tray: Removal
- Refitting) (MR 392, 80A, Battery),
- the air filter unit (see Air filter unit: Removal - Refitting)
(MR 392, 12A, Fuel mixture),
- the air filter box outlet air pipe,
- the front left-hand wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, 35A-1).
II - OPERATION FOR REMOVAL OF PART
CONCERNED

- Loosen the brake pipe nut (1) on the master cylinder.

- Loosen the brake pipe nut (2) on the brake hose.
WARNING
Prepare for the flow of fluid, and protect the surrounding
components.

- Unclip the brake pipe at (3).
- Remove the brake pipe.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
- Refit the brake pipe.
- Screw on:
- the brake pipe nut on the master cylinder,
- the brake pipe nut on the brake hose.
- Torque tighten:
- the brake pipe nut on the master cylinder (17
Nm),
- the brake pipe nut on the brake hose (14 Nm).
- Attach the brake pipe.
II - FINAL OPERATION.
- Bleed the brake circuit (see 30A, General information,
Braking circuit: Bleed, 30A-4).
- Refit:
- the front left-hand wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, 35A-1),
- the air filter box outlet air pipe,
- the air filter unit (see Air filter unit: Removal - Refitting)
(MR 392, 12A, Fuel mixture),
- the battery protective shield (see Battery tray: Removal
- Refitting) (MR 392, 80A, Battery),
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery),
- the air filter box air inlet pipe,
- the engine undertray,
- the engine cover.
READ NEXT:
LEFT-HAND DRIVE, and WITHOUT ANTI-LOCK BRAKING SYSTEM
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equi
LEFT-HAND DRIVE
REMOVAL
I - REMOVAL PREPARATION OPERATION
K4J or K4M or K9K
Remove the engine cover.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Disconnect the non-return valve (1) at the servo
SEE MORE:
Before removing the clutch, check:
The direction of fitting for the clutch plate.
Before refitting the clutch, check:
The flywheel friction track (no scratches or blue
stains),
The crankshaft bearing (no sticking),
The engine and gearbox seals (replace if necessary),
The sliding action of
D4F, and 740 or 742 or 764
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery).
Remove:
the air filter unit (see
© 2016-2023 Copyright www.rclio.com
